How long does a CO2 tank last? Calculator for beer taps, soda makers and MAG welding

A 2 kg CO2 cylinder pours about 187–412 L of beer at 1.5 bar. In a soda maker it makes up to 282 L of sparkling water, as much as 4.7 soda-maker cylinders of 425 g. For MAG welding at 10 L/min it lasts about 1.8 hours. Choose your use and cylinder size below to see how many weeks one fill lasts.

Work out how long your CO2 lasts

What do you use the CO2 for?
Beer per week
L/week

A 20 L keg every two weeks is 10 L a week.

Keg pressure
bar

Read it on the regulator gauge, in bar above atmospheric pressure. The higher the pressure, the more CO2 each litre of beer uses.

Cylinder size (kg of CO2)
kg

This is the weight of the CO2 inside, not of the cylinder. A 2 kg cylinder weighs about 4.5 kg empty and 6.5 kg full.

A 2 kg fill lasts

19–41 weeks

≈ 4.3–9.5 months

Per fill: 187–412 L of beer

2 kg of CO2 = 4.7 × a 425 g soda-maker cylinder

Every cylinder size at your consumption
CylinderBeer per fill (L)Lasts (weeks)= 425 g cylinders
425 g40–874.0–8.71.0 ×
640 g60–1326.0–131.5 ×
2 kg187–41219–414.7 ×
3.75 kg351–77235–778.8 ×
6 kg561–1,23556–12314.1 ×
7.5 kg702–1,54470–15417.6 ×
10 kg936–2,05894–20623.5 ×

Assumes a keg at 1.5 bar and 5 °C. The low figure counts only the CO2 that replaces the beer you pour: 4.9 g per litre. The high figure is 10.7 g per litre, 2.2 times as much. That matches the US rule of thumb of 1 lb of CO2 per half-barrel keg, which covers purging, keg changes and small leaks.

Beer tap · 2 kg19–41 weeks

How the calculator works

  1. Weeks per fill = CO2 in the cylinder (g) ÷ CO2 per litre or per hour (g) ÷ your litres or hours per week.
  2. Beer tap: each litre of beer you pour is replaced in the keg by a litre of CO2 at keg pressure. At 1.5 bar and 5 °C that litre of gas weighs 4.9 g (real-gas density from CoolProp). The upper figure, 10.7 g, is 2.2 times as much. That multiple comes from the US rule of 1 lb of CO2 per half-barrel keg (58.7 L) at 12 psi, which includes the losses of a real tap.
  3. Soda maker: SodaStream rates a 425 g cylinder at up to 60 L, which is 7.1 g per litre. That is the best case. Stronger carbonation uses more.
  4. MAG welding: 1 kg of CO2 gives 541 L of gas at 15 °C and 1 bar (CoolProp). Gas per hour of arc time is the flow in L/min × 60.

Real systems differ, so some results are ranges. A leak shortens every figure. If a full cylinder empties much faster than the calculator says, brush soapy water on the joints and look for bubbles. For a planted tank, use the aquarium CO2 calculator.

Sources

CO2 density and gas volume per kg: CoolProp 8.0 (real-gas equation of state), computed October 2026. Soda makers: SodaStream, spare CO2 cylinder page, “up to 60 L” per cylinder depending on carbonation. Beer: KegWorks, 5 lb CO2 tank, 5 to 7 half kegs; Micro Matic, 5 lb CO2 cylinder, 6 to 8 half kegs; Kegoutlet, about 1 lb of CO2 per half-barrel keg. Welding: Linde, “MAG-Schweißen: So machen es die Profis”, 10 to 12 L/min short arc, 15 to 20 L/min spray arc, wire diameter × 10. Status: October 2026.

FAQ: Questions about CO2 cylinder life

It depends on what you use it for. On a beer tap at 1.5 bar it pours about 187–412 L of beer, which is 19–41 weeks at 10 L a week. In a soda maker it makes up to 282 L of sparkling water, or 28 weeks at 10 L a week. For MAG welding at 10 L/min it gives about 1.8 hours of arc time.

A 5 lb tank holds 2.27 kg of CO2, a little more than a 2 kg cylinder. On a beer tap at 1.5 bar that is about 212–467 L of beer. US keg suppliers quote 5 to 8 half-barrel kegs (about 290 to 470 L) for dispensing alone.

At minimum, CO2 at keg pressure has to fill the space left by the beer you pour. That is about 3.9 g per litre at 1 bar and 4.9 g at 1.5 bar (5 °C). A real tap uses more because of purging, keg changes and small leaks. The US rule of 1 lb per half-barrel keg comes to 2.2 times that minimum.

4.7. SodaStream rates each 425 g cylinder at up to 60 L of water, so a 2 kg fill makes up to 282 L. With our hose kit (W21.8 to Quick Connect), a 2 kg cylinder works with SodaStream Terra, DUO and Art machines. We have not tested it on older machines with screw-in cylinders.

Check for leaks first. A missing seal, a loose nut or a worn keg coupler can empty a cylinder within days. With the gas on, brush soapy water on every joint and watch for bubbles. Higher keg pressure and warm kegs also raise consumption. On a welder, long pre-flow and post-flow times add up.

Embed this calculator

You may embed the calculator in blogs, forums and guides for free, without signing up. Please keep the credit line.

Included in the code: “Calculator by intergases.com”
Credit preview
Calculator by intergases.com

These values are a guide. Your regulator, the markings on the cylinder and the machine maker’s instructions take priority.